Basic Setup

Creation date: 30/03/2022 09:04    Updated: 30/03/2022 09:35
This guide will go over the layout for the settings pages of the DX and DL range of DVRs

Accessing the Menu - Using a remote

  -  Press the SETUP button on the remote and enter the password (default is eagle)

Accessing the Menu - Using Touchscreen monitor

  -  Tap the screen to bring up the options along the bottom of the screen, then tap the Login icon in the bottom right corner (see image below)



BASIC SETUP
Click setup button and enter the following interfaces:

REGISTER INFORMATION (SETUP VEHICLE INFORMATION)
➢ Register information Device info:


Device ID: Currently, it is not useful.
➢ Register information Vehicle info


Vehicle Number
When connected with PAD, the vehicle number is needed.
Vehicle plate: Input manually.
Line number: Input manually.

➢ Register information Driver info:


Driver number: Input manually.
Driver name: Input manually.

TIME SETUP
➢ Time setup General
Date format: Setup the date format of device
Time format: 24 hours or 12 hours
Time zone: Range from 12 th district ~ +13 th district


➢ Time Time Sync


Date/Time: Device time, from 2000 01 01 to 2036 12 31
Satellite: Synchronize time with GPS satellite. Once GPS signal changes to valid, device will
synchronize time
Center Server: synchronize time with center server
NTP sync: synchronize time with NTP server
Remark:
1) Synchronize time according to time zone
2) Multi mode can be selected for time synchronization. If one works, the others take no affect.
Otherwise, it switches to another sync mode every 5 minutes.

➢ Time setup DST


Enable: Select to enable
Offset: After enabling DST, adjust the hour manually
Mode: Setup DST according to week or date
Start: Time to start DST
End: Time to end DST

START UP
➢ Startup ON/OFF


ON/OFF mode: 3 modes, including ignition, timer and ignition or timer.
Ignition: Input ignition delay time for shutdown delay function
Timer: When setup the start mode as Timer, please setup the start time a nd end time
Under this mode, MDVR’s start up or shut down time will not affect the ignition.
Remark:If use setup as Ignition or Timer Mode, Ignition ON or Timer start time can trigger MDVR start up. And only when Ignition off and Timer end time, MDVR will shut down.

➢ Start Sleep


Sleep Mode: Currently, there is only no consumption standby mode available.
Low Voltage protect: Enabling the low voltage shutdown protection mode selected.
Battery low voltage: Protect the vehicle battery. When consistently below the standard value, it will
countdown shutdown. As for a 12V vehicle, the default is 9V, while a 24V vehicle is 21V.
Voltage start up: low voltage protection, when the battery voltage is consistently greater than the
standard value, it will automatically boot. As for a 12V vehicle, the default is 12.5V, while a 24V
vehicle is 24.5 V.
Low volt upload: The low voltage protection will be reported to the platform after it is ticked.

USER SET UP
In the basic settings, click user settings, enter the following interface, user can enter setting menu.


User name: The default ones are admin and user.
User Group: It is divided into administrator and ordinary user.
It supports delete user function. Select the user and click "Delete User" button. Please be noted that the administrator cannot be deleted.
It supports add user function. Click "Add User" button, then enter the following interface.



1) Only administrators can add users.
2) Users can add up to two.
3) User name cannot be empty, not the same with the existed user name while the user password can be empty.
User name and password can be modified . Select a user, click the "Edit User" button, enter the following interface:


Modify the user name and password to confirm the operation temporarily. There is no need to
verify the old password, Administrator user name cannot be modified.

NETWORK
In the basic settings, click Network Settings, enter the following interface, user can set network
parameters.
➢ Network Local


Automatically obtain IP:
Dynamic acquisition, DN S can also be statically configured to dynamically obtain.
Use the following IP: Static IP, need to use a static DNS.
Switch from static IP to automatically obtain IP mode, it can display dynamic IP, but the static IP
parameters will not be covered , to restore the last saved static IP after switching.

➢ Network Settings Ports


➢ Network WIFI  (Not Supported in our Models)


Enable:
Select to enable WIFI
ESSID: Manually input the address of AP
Encryption: It supports NONE, WEP and WPA
Password:  Manually input
Static IP: Select to use static IP, or MDVR will get dynamic IP

➢ Network Communication:
Dialing wireless network, user needs to choose the module type and setup dialing parameters


When entering the dialing setup interface, it searches the wireless module type automatically. It shows No Service when there is no module.
Network type: The default one is Mix, 2G/3G and 2G/3G/4G optional.
Dialing parameter It includes access point, user name, password, data service number, and enter SIM  parameters provided by the manufacturer. The default is empty, the program comes with empty arguments by dialing.
Certification: Supports PAP or CHAP.

When there is SIM fitted and normal 3G/4G signal, it will dial automatically.

All Settings are Programmed prior to DVR being supplied.
For Our Network setting please click here for guide.

➢ Network Server


Center server: It supports 6 servers at most, and server 1 cannot be deleted manually.
ON: Enable the current server.
Protocol type: The default one is N9M.
Enable network: There is local, WIFI and module optional
Register server address: To run the registration server address.
Registration server port: To run the registration server port.
Media server address: To run the media server address.
Media server port: To run the media server port.



APPLICATION
➢ Application FTP Client


FTP Enable:
Enable FTP . (The FTP here is normally used to keep the
Server: To run FTP server address.
Port: To run FTP server port. (The default one is 21.)
User name/password: The accounts distributed by FTP server.


Files